Evco c-pro kilo Manual de usuario Pagina 1

C-PRO KILO PROGRAMMABLE CONTROLLERS HARDWARE MANUAL CODE 114CPRKHWE01

C-PRO KILO HARDWARE MANUAL Page 10 3 Technical characteristics 3.1 Connections Power supply: The C-PRO KILO is powered by 24 VAC. It can also b

C-PRO KILO HARDWARE MANUAL Page 11 Connection with a remote expansion (or another CAN controller): The connection between C-PRO KILO and the remote

C-PRO KILO HARDWARE MANUAL Page 12 3.2 C-PRO KILO electrical connections (wiring) The C-PRO KILO controller wiring layout is shown below, along wi

C-PRO KILO HARDWARE MANUAL Page 13 JA Connector for analogue signals Conn. Abbrev. Description JA-1 AI1 Analogue input No.1 (for NTC probes) JA-

C-PRO KILO HARDWARE MANUAL Page 14 JF: Controller power supply connector Conn. Abbrev. Description JF-1 V≅ Controller power supply (24 VAC / 20

C-PRO KILO HARDWARE MANUAL Page 15 3.3 C-PRO KILO dimensions/installation The mechanical dimensions of the C-PRO KILO are indicated below; the mea

C-PRO KILO HARDWARE MANUAL Page 16 Open case versions 10 DIN modules. Recommendations for installation: - ensure that the operating condition

C-PRO KILO HARDWARE MANUAL Page 17 To install the C-PRO KILO, proceed as indicated in the diagrams (points 1 and 2). To remove the C-PRO KILO, use

C-PRO KILO HARDWARE MANUAL Page 18 3.4 General characteristics Applicable safety regulations EN60730-1 Purpose of the device Programmable electr

C-PRO KILO HARDWARE MANUAL Page 19 3.6 Electrical characteristics CPU Microcontroller 8 bit Program flash 128kB Data memory RAM 4kB EEPR

C-PRO KILO HARDWARE MANUAL Page 2 Important Please read these instructions carefully prior to installation and use, and follow all the

C-PRO KILO HARDWARE MANUAL Page 20 Current measurement sensitivity Type Voltage measurement range Voltage measurement accuracy Voltage measureme

C-PRO KILO HARDWARE MANUAL Page 21 Note: 1) baud rate selectable by parameters 2) The CAN connection consists of a cable with twisted pair (both

C-PRO KILO HARDWARE MANUAL Page 22 4 The C-PRO KILO user interface There are 3 C-PRO KILO built-in versions: - with 4 x 20 character alphanumeric

C-PRO KILO HARDWARE MANUAL Page 23 Predefined as ENTER • 1st level programming command (pressed for 3 s) • confirm value/send command (pressed and

C-PRO KILO HARDWARE MANUAL Page 24 Version with LED display and refrigeration or air-conditioning icons The display consists of four red digits (p

C-PRO KILO HARDWARE MANUAL Page 25 The following table gives the meanings of the front panel icons: ICON COLOUR Summer Icon (air-conditioning displ

C-PRO KILO HARDWARE MANUAL Page 26 5 C-PRO EXP KILO I/O expansion units The C-PRO EXP KILO I/O expansion units allow expansion of the controller I

C-PRO KILO HARDWARE MANUAL Page 27 C-PRO EXP KILO Closed case version C-PRO EXP KILO Open version

C-PRO KILO HARDWARE MANUAL Page 28 5.1 C-PRO EXP KILO electrical connections (wiring) The C-PRO EXP KILO controller wiring layout is shown below

C-PRO KILO HARDWARE MANUAL Page 29 JA Connector for analogue signals Conn. Abbrev. Description JA-1 AI1 Analogue input No.1 (for NTC probes) JA-2

C-PRO KILO HARDWARE MANUAL Page 3 Contents 1 INTRODUCTION...

C-PRO KILO HARDWARE MANUAL Page 30 JF: Expansion unit power supply connector Conn. Abbrev. Description JF-1 V≅ Expansion unit power supply (24 VAC/

C-PRO KILO HARDWARE MANUAL Page 31 5.2 C-PRO EXP KILO dimensions/installation The mechanical dimensions of the C-PRO EXP KILO are indicated below;

C-PRO KILO HARDWARE MANUAL Page 32 - in compliance with safety regulations, the device must be installed correctly, and in such a way as to protect

C-PRO KILO HARDWARE MANUAL Page 33 6 Accessories 6.1 User terminals (IntraBus) User terminals allow remote management of the controller (displ

C-PRO KILO HARDWARE MANUAL Page 34 6.1.1 V LEDi dimensions/installation The V LEDi mechanical dimensions are given below; the measurements are ex

C-PRO KILO HARDWARE MANUAL Page 35 CI connector: Control unit connection connector Conn. Abbrev. Description CI-1 1 V LEDi power supply (12 VDC);

C-PRO KILO HARDWARE MANUAL Page 36 The following table gives the meanings of the front panel LEDs: ICON COLOUR Summer Icon Red Winter Icon Red Comp

C-PRO KILO HARDWARE MANUAL Page 37 6.1.5 V WALL electrical connections, when the user terminal has an independent power supply The V WALL user ter

C-PRO KILO HARDWARE MANUAL Page 38 6.1.6 V WALL electrical connections, when the user terminal is powered from the controller The V WALL user term

C-PRO KILO HARDWARE MANUAL Page 39 6.1.7 V WALL user interface The display consists of four red digits (plus decimal points) and 6 icons; the keyp

C-PRO KILO HARDWARE MANUAL Page 4 1 Introduction The C-PRO KILO family of programmable controllers is the ideal solution for low to medium complex

C-PRO KILO HARDWARE MANUAL Page 40 The following table gives the meanings of the front panel LEDs: LED COLOUR L0 Red L1 Red L2 Red L3 Red L4 Red L

C-PRO KILO HARDWARE MANUAL Page 41 6.2 Remote User interface (CAN) The user interfaces allow to install a display and keyboard remotely far from t

C-PRO KILO HARDWARE MANUAL Page 42 The following table summarizes the keyboard button meaning: BUTTONS MAIN FUNCTION SECONDARY FUNCTION Predefi

C-PRO KILO HARDWARE MANUAL Page 43 6.2.1.2 V-VIEW wiring layout 6.2.1.3 V-VIEW specifications General specifications Safety standards referen

C-PRO KILO HARDWARE MANUAL Page 44 Type CAN V2.0B not optoisolated Physical Layer 2 wires + common, ISO 11898 standard Baud rate (L max. = 10 m)

C-PRO KILO HARDWARE MANUAL Page 45 6.3 EVDFAN1 phase chopping speed regulator The EVDFAN1 is a phase chopping speed regulator for controlling sing

C-PRO KILO HARDWARE MANUAL Page 46 6.3.1 EVDFAN1 electrical connections (wiring) The EVDFAN1 module wiring layout is shown below, with a table giv

C-PRO KILO HARDWARE MANUAL Page 47 6.4 Control and monitoring accessories These modules allow the conversion of signals from TTL to RS-485 (with or

C-PRO KILO HARDWARE MANUAL Page 48 6.4.3 EVIF21TS7I electrical connections The EVIF21TS7I interface wiring layout is shown below, with a table givi

C-PRO KILO HARDWARE MANUAL Page 49 6.5 Programming accessories 6.5.1 EVKEY programming key The EVKEY programming key allows configuration

C-PRO KILO HARDWARE MANUAL Page 5 The following table illustrates the main features of the C-PRO KILO: Dimensions Power supply Analogue inputs (1) D

C-PRO KILO HARDWARE MANUAL Page 50 6.5.3 EVPROG programming kit The EVPROG programming kit allows programs to be downloaded to the C-PRO

C-PRO KILO HARDWARE MANUAL Page 51 7 CAN Connection C-PRO KILO can be connected to other controllers, to expansion modules and to one or more user

C-PRO KILO HARDWARE MANUAL Page 52 7.1 Notes on the parameter of the controller relative to the CAN net configuration To log on the controller p

C-PRO KILO HARDWARE MANUAL Page 53 The main parameters of the CAN net are the following : • “My Node” (represents the data sender ID ) • “Network

C-PRO KILO HARDWARE MANUAL Page 54

C-PRO KILO HARDWARE MANUAL Page 55 C-PRO KILO Hardware manual. Version 1.01, January 2009. Code 114CPRKHWE01. File 114CPRKHWE01.pdf. This document i

HEAD OFFICE Evco Via Mezzaterra 6, 32036 Sedico Belluno ITALY Tel: 0437 852468 Fax: 0437 83648 [email protected] www.evco.it OVERSEAS OFFICES Control

C-PRO KILO HARDWARE MANUAL Page 6 C-PRO KILO Built-in version with 4 x 20 character alphanumeric display C-PRO KILO Built-in version with LED dis

C-PRO KILO HARDWARE MANUAL Page 7 C-PRO KILO Closed case version C-PRO KILO Open version

C-PRO KILO HARDWARE MANUAL Page 8 2 Components and accessories 2.1 Example for built-in versions

C-PRO KILO HARDWARE MANUAL Page 9 2.2 Example for closed case versions